[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[pbsd-mg2] Re: EZ-GIG
取り敢えず dumpcis 出来るようには成ったので・・・
FreeBSD 4.0-current での pccardc dumpcis です。
# 当然 PAO は無い
おまけで Xpress Doc の物も付けておきます。
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
000: d8 00 ff
Common memory device information:
Device number 1, type Function specific, WPS = ON
Speed = No speed, Memory block size = 512b, 1 units
Tuple #2, code = 0x15 (Version 1 info), length = 24
000: 04 01 41 70 72 69 63 6f 72 6e 00 41 54 41 20 50
010: 43 20 43 61 72 64 00 ff
Version = 4.1, Manuf = [Apricorn],card vers = [ATA PC Card]
Tuple #3, code = 0x18 (JEDEC descr for common memory), length = 2
000: df 01
Tuple #4, code = 0x20 (Manufacturer ID), length = 4
000: f9 01 00 00
PCMCIA ID = 0x1f9, OEM ID = 0x0
Tuple #5, code = 0x21 (Functional ID), length = 2
000: 04 01
Fixed disk card - POST initialize
Tuple #6, code = 0x22 (Functional EXT), length = 2
000: 01 01
Modem interface capabilities:
Tuple #7, code = 0x22 (Functional EXT), length = 3
000: 02 08 7f
Data modem services available:
Tuple #8, code = 0x1a (Configuration map), length = 5
000: 01 03 00 02 0f
Reg len = 2, config register addr = 0x200, last config = 0x3
Registers: XXXX----
Tuple #9, code = 0x1b (Configuration entry), length = 5
000: c0 f0 01 01 55
Config index = 0x0(default)
Interface byte = 0xf0 (memory) BVD1/2 active, card WP active, +RDY/-BSY active, wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Tuple #10, code = 0x1b (Configuration entry), length = 9
000: c1 f1 19 01 55 64 f0 ff ff
Config index = 0x1(default)
Interface byte = 0xf1 (I/O) BVD1/2 active, card WP active, +RDY/-BSY active, wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Card decodes 4 address lines, full 8/16 Bit I/O
IRQ modes: Level, Pulse
IRQ level = 4
Tuple #11, code = 0x1b (Configuration entry), length = 15
000: c2 f1 99 01 55 ea 61 f0 01 07 f6 03 00 ee 02
Config index = 0x2(default)
Interface byte = 0xf1 (I/O) BVD1/2 active, card WP active, +RDY/-BSY active, wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Card decodes 10 address lines, full 8/16 Bit I/O
I/O address # 1: block start = 0x1f0 block length = 0x8
I/O address # 2: block start = 0x3f6 block length = 0x1
IRQ modes: Level, Pulse, Shared
IRQ level = 14
Max twin cards = 2
Misc attr:
Tuple #12, code = 0x1b (Configuration entry), length = 15
000: c3 f1 99 01 55 ea 61 70 01 07 76 03 00 ef 02
Config index = 0x3(default)
Interface byte = 0xf1 (I/O) BVD1/2 active, card WP active, +RDY/-BSY active, wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Card decodes 10 address lines, full 8/16 Bit I/O
I/O address # 1: block start = 0x170 block length = 0x8
I/O address # 2: block start = 0x376 block length = 0x1
IRQ modes: Level, Pulse, Shared
IRQ level = 15
Max twin cards = 2
Misc attr:
Tuple #13, code = 0x14 (No link), length = 0
Tuple #14, code = 0xff (Terminator), length = 0
Code 136 not found
Code 136 not found
code Unknown ignored
code Manufacturer ID ignored
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
000: 00 00 ff
Common memory device information:
Device number 1, type No device, WPS = OFF
Speed = No speed, Memory block size = 512b, 1 units
Tuple #2, code = 0x15 (Version 1 info), length = 89
000: 04 01 4d 69 63 72 6f 74 65 63 68 20 49 6e 74 65
010: 72 6e 61 74 69 6f 6e 61 6c 20 49 6e 63 2e 00 49
020: 44 45 20 50 43 43 41 52 44 00 28 43 29 20 41 52
030: 43 48 4f 53 20 53 2e 41 2e 20 31 39 39 35 2d 39
040: 37 20 46 61 78 20 2b 33 33 20 31 20 36 30 20 31
050: 33 20 39 39 20 31 38 00 ff
Version = 4.1, Manuf = [Microtech International Inc.],card vers = [IDE PCCARD]
Addit. info = [(C) ARCHOS S.A. 1995-97 Fax +33 1 60 13 99 18]
Tuple #3, code = 0x1a (Configuration map), length = 5
000: 01 10 00 02 01
Reg len = 2, config register addr = 0x200, last config = 0x10
Registers: X-------
Tuple #4, code = 0x1b (Configuration entry), length = 14
000: c1 81 1e 01 55 01 0e ea 4f 4f 64 30 ff ff
Config index = 0x1(default)
Interface byte = 0x81 (I/O) wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Vpp pwr:
Nominal operating supply voltage: 1.2 x 10V
Wait scale Speed = 4.0 x 10 ms, scaled by 100
RDY/BSY scale Speed = 4.0 x 10 ms, scaled by 100
Card decodes 15 address lines, limited 8/16 Bit I/O
IRQ modes: Pulse
IRQ level = 15
Tuple #5, code = 0x20 (Manufacturer ID), length = 4
000: 41 52 43 00
PCMCIA ID = 0x5241, OEM ID = 0x43
Tuple #6, code = 0x21 (Functional ID), length = 2
000: 04 00
Fixed disk card
Tuple #7, code = 0x22 (Functional EXT), length = 2
000: 01 01
Modem interface capabilities:
Tuple #8, code = 0x14 (No link), length = 0
Tuple #9, code = 0xff (Terminator), length = 0
Code 136 not found
Code 136 not found
code Unknown ignored
code Manufacturer ID ignored