Re: Call for Cassiopeia E series status report.

[yukihiko@yk.rim.or.jp (Sano Yukihiko)]

佐野です。

E-500 は、Linux-VR 入れて、mgdm のテストに使ってます。

<200103050227.LAA13716@shin1.sm.sony.co.jp>の記事において
takemura@netbsd.orgさんは書きました。

>> するための作業です。もちろん、コンフィギュレーションを書き換えて
>> カーネルを再コンパイルして実験するのもアリです。
新しい CF を買ったので、ちょっと試してみました。

GENERIC の CASIO_CASSIOPEIAE_E55 を CASIO_CASSIOPEIAE_E500 に換えた
カーネルです。
# カーネルのソースは、たまたま手元にあったものです。
# 本業の方が忙しいので、インストールはまだしてません。

% cu -l /dev/tty00 -s 9600
Connected.
mem_cluster_cnt = 2
mem_clusters[0] = {0x0,0x25e000}
mem_clusters[1] = {0x25e000,0x1da2000}
loading 0x25e000,0x1da2000
Copyright (c) 1996, 1997, 1998, 1999, 2000
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.5.1_ALPHA (E500) #0: Sat Mar 10 01:19:16 JST 2001
    hiko@Kano:/home/hiko/HPCmips/kernel/src/sys/arch/hpcmips/compile/E500
CASIO Cassiopeia E500 (NEC VR4121 rev1.0 131.072MHz)
total memory = 32768 KB
avail memory = 27756 KB
using 435 buffers containing 1740 KB of memory
../../../../arch/hpcmips/vr/vr.c(294): vr_bus_reset() not implemented.
mainbus0 (root)
cpu0 at mainbus0: NEC VR4100 CPU (0xc60) Rev. 6.0 with software emulated floating point Rev. 0.0
cpu0: L1 cache: 16KB/16B instruction, 8KB/16B data, direct mapped
cpu0: No L2 cache
cpu0: install VR specific idle routine
vrip0 at mainbus0
vrcmu0 at vrip0 addr 0xb000060-0xb00007f
vrgiu0 at vrip0 addr 0xb000100-0xb00011f intr 8
button0 at vrgiu0 port=6 id=1 active=low sense=edge
button1 at vrgiu0 port=7 id=2 active=low sense=edge
button2 at vrgiu0 port=8 id=9 active=low sense=edge
button3 at vrgiu0 port=9 id=10 active=low sense=edge
button4 at vrgiu0 port=10 id=11 active=low sense=edge
button5 at vrgiu0 port=11 id=12 active=low sense=edge
button6 at vrgiu0 port=12 id=4 active=low sense=edge
button7 at vrgiu0 port=13 id=3 active=low sense=edge
pwctl0 at vrgiu0 port=38 id=0 on=1
pwctl1 at vrgiu0 port=26 id=4 on=1
vrbcu0 at vrip0 addr 0xb000000-0xb00001f
vrbcu: cpu 131.072MHz, bus 32.768MHz, ram 32.768MHz
com0 at vrip0 addr 0xc000000-0xc000007 intr 9: ns16550a, working fifo
com0: console
vrrtc0 at vrip0 addr 0xb0000c0-0xb0000df intr 2
vrkiu0 at vrip0 addr 0xb000180-0xb00019f intr 7
wskbd0 at vrkiu0 mux 1
vrpmu0 at vrip0 addr 0xb0000a0-0xb0000bf intr 1
vrpmu: GPIO[0] activation
vrpmu: Deadman's switch detected
vrdsu0 at vrip0 addr 0xb0000e0-0xb0000e7
vrpiu0 at vrip0 addr 0xb000120-0xb0002bf intr 5
wsmouse0 at vrpiu0 mux 0
vrisab4 at vrgiu0:ISA port 0x1400c000-0x18000000 mem 0x10000000-0x20000000
isa4 at vrisab4
wdc0 at isa4 port 0x170-0x177 irq 33554435
wd0 at wdc0 channel 0 drive 0: <LEXAR ATA_FLASH>
wd0: drive supports 1-sector pio transfers, lba addressing
wd0: 64256 KB, 1004 cyl, 4 head, 32 sec, 512 bytes/sect x 128512 sectors
bivideo0 at mainbus0: pseudo video controller
hpcfb0 at bivideo0: hpcrasops 240x320 pixels, 65536 colors, 30x32 chars: tvram redraw
wsdisplay0 at hpcfb0
wsdisplay0: screen 0 added (std, vt100 emulation)
btnmgr0 at mainbus0
wskbd1 at btnmgr0 mux 1
hpcapm0 at mainbus0: pseudo power management module
apmdev0 at hpcapm0: Power Management spec V1.2
../../../../arch/hpcmips/vr/vr.c(294): vr_bus_reset() not implemented.
boot device: wd0
root on wd0a dumps on wd0b
wd0: no disk label
no file system for wd0 (dev 0x100)
cannot mount root, error = 79
root device (default wd0a): 
Disconnected.