Re: KUROBOX Works!

[UMENO Takashi <umeno@rr.iij4u.or.jp>]

こんばんは、かわうちさん。うめのと申します。

こちらでもNetBSDを玄箱を移植しようとしていたのですが、
結局シングルユーザモードでの/sbin/initのprintf()の出力を見るところまで至りませんでした。

かわうちさんが移植したNetBSD/sandpointをこれからつかって
うちの玄箱でNetBSDを動かしてみようと思います。かわうちさん、どうもありがとうございます。

なお、こちらの移植ではここまでしかできませんでした...。

(@@)(@@)SREC_END
First Load Addr = 00C00000
Last  Load Addr = 00CF3D5E
Total Size      = 000F3D5F (998751) Bytes
>RET:0 OK
# setimage 00c00000 -f

******* Product Information *******
----------------------------------
Product Name: KURO-BOX(IETSUNA)
          VER: 1.02
         Date: 2005/8/18 23:48:23
----------------------------------
Firmware check: OK.
zimage start: 00C0006C end: 00CF3D5F size: 000F3CF3
initrd start: 00904000 end: 00B0B647 size: 00207647
>RET:0 OK
# gunzip 00c0006c 000f3cf3 00090000
gunzip 00C0006C-018000D8 (00C0006C) -> 00090000-00490000 (00400000)
Uncompressing memory block ...
done.
>RET:0 OK
# call 00090000
call address = 00090000
bceqend initppc()
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 3.99.3 (GENERIC.kurobox) #94: Thu Aug 18 23:47:00 JST 2005
	umeno@belldandy.unnumbered.net:/export/home/umeno/kurobox/20050515/netbs
d-kurobox/src/sys/arch/kurobox/compile/GENERIC.kurobox
total memory = 65536 KB
avail memory = 60720 KB
mainbus0 (root)
cpu0 at mainbus0: Version 0x8081 (Revision 0x1014), ID 0 (primary)
cpu0: HID0 908000<DOZE,DPM,ICE>
pci0 at mainbus0
pci0: i/o space, memory space enabled
vendor 0x1057 product 0x0006 (host bridge, revision 0x14) at pci0 dev 0 function
 0 not configured
tlp0 at pci0 dev 11 function 0: ADMtek AN985 Ethernet, pass 1.1
tlp0: broken MicroWire interface detected; setting SROM size to 1Kb
pci_intr_map: pin=1 line=11
exec pci_intr_establish(): ih = 0x0
tlp0: interrupting at irq 0
tlp0: Ethernet address 00:00:00:00:00:00
cmdide0 at pci0 dev 12 function 0
cmdide0: Silicon Image 0680 (rev. 0x02)
cmdide0: bus-master DMA support present
cmdide0: primary channel wired to native-PCI mode
pci_intr_map: pin=1 line=12
exec pci_intr_establish(): ih = 0x1
cmdide0: using irq 1 for native-PCI interrupt
atabus0 at cmdide0 channel 0
cmdide0: secondary channel wired to native-PCI mode
atabus1 at cmdide0 channel 1
ohci0 at pci0 dev 14 function 0: vendor 0x1033 product 0x0035 (rev. 0x43)
pci_intr_map: pin=1 line=14
exec pci_intr_establish(): ih = 0x3
ohci0: interrupting at irq 3
ohci0: OHCI version 0.0
ohci0: unsupported OHCI revision
ohci0: init failed, error=4
ohci1 at pci0 dev 14 function 1: vendor 0x1033 product 0x0035 (rev. 0x43)
pci_intr_map: pin=2 line=14
exec pci_intr_establish(): ih = 0x3
ohci1: interrupting at irq 3
ohci1: OHCI version 0.0
ohci1: unsupported OHCI revision
ohci1: init failed, error=4
ehci0 at pci0 dev 14 function 2: vendor 0x1033 product 0x00e0 (rev. 0x04)
pci_intr_map: pin=3 line=14
exec pci_intr_establish(): ih = 0x3
ehci0: interrupting at irq 3
ehci0: EHCI version 0.0
usb0 at ehci0: USB revision 2.0
uhub0 at usb0
uhub0: vendor 0x1033 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub0: 0 ports with 0 removable, self powered
uhub0: no ports, hub ignored
usb0: root device is not a hub
eumb0 at mainbus0
opb0 at mainbus0
com0 at opb0 addr 0x80004600 irq 14: ns16550a, working fifo
com0: console
com1 at opb0 addr 0x80004500 irq 13: ns16550a, working fifo
biomask a netmask b ttymask b
wd0 at atabus0 drive 0: <HDS722516VLAT80>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 153 GB, 319120 cyl, 16 head, 63 sec, 512 bytes/sect x 321672960 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(cmdide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
boot device: <unknown>
root device: wd0a
dump device (default wd0b): 
file system (default generic): 
root on wd0a dumps on wd0b
mountroot: trying ffs...
root file system type: ffs
exec inittodr()
exec inittodr(): base = 1123171142
WARNING: CHECK AND RESET THE DATE!
init path (default /sbin/init): 
init: copying out flags `-s' 3
init: copying out path `/sbin/init' 11

******* Product Information *******
----------------------------------
Product Name: KURO-BOX(IETSUNA)
          VER: 1.01
         Date: 2004/3/18 11:42:44
----------------------------------
Firmware check: OK.

--
梅野 崇