Re: UCONS(trap 380) or PS3(trap 600) (Re: Serial speed ?

[Tsubai Masanari <DX0f@segv.jp>]

>UCONS を使った時: (画面の表示です)

>trap type 380 at 2f93ac
>Stopped in pid 0.1 () at  netbsd:.uscons_usbd_transfer+0x9c:	ld

まあこれはともかく。:-)

>それで、PS3 を使った時には、次のようになります。
>http://www.ki.nu/hardware/.ps3/image/IMG_7892.JPG

私の所ではだいたい動いてるみたいなんですよね。slogin して dmesg できる
ぐらいには。-D 2007-06-16-UTC のソースです。

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.99.20 (PS3) #0: Wed Jul  4 03:00:47 JST 2007
	tsubai@sakura:/a/0616/src/sys/arch/ps3/compile/PS3
total memory = 128 MB
avail memory = 115 MB
cpu 3.2 GHz, timebase 80 MHz
mainbus0 (root)
cpu0 at mainbus0: Cell (Revision 501), ID 0 (primary)
rsxfb0 at mainbus0: 720 x 480, 32bpp
wsdisplay0 at rsxfb0: console (std, vt100 emulation)
obio0 at mainbus0
gelic0 at obio0: irq 50 address 00:19:c5:26:79:f0
ohci0 at obio0: irq 16
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: PS3 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
ehci0 at obio0: irq 10
ehci0: EHCI version 1.0
ehci0: companion controller, 2 ports each: ohci0
usb1 at ehci0: USB revision 2.0
uhub1 at usb1
uhub1: PS3 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ohci1 at obio0: irq 17
ohci1: OHCI version 1.0
usb2 at ohci1: USB revision 1.0
uhub2 at usb2
uhub2: PS3 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci1 at obio0: irq 11
ehci1: EHCI version 1.0
ehci1: companion controller, 2 ports each: ohci1
usb3 at ehci1: USB revision 2.0
uhub3 at usb3
uhub3: PS3 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
flash0 at obio0
ps3d0 at obio0: type 0, 4 region(s), blksize 512, 117210240 blocks
ps3d0: irq 51
scsibus0 at ps3d0: 2 targets, 1 lun per target
ps3d1 at obio0: type 5, 1 region(s), blksize 2048, 2147483647 blocks
ps3d1: irq 52
scsibus1 at ps3d1: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <SCEI, PS3 SATA, 4989> disk fixed
sd0: 57231 MB, 116280 cyl, 16 head, 63 sec, 512 bytes/sect x 117210240 sectors
cd0 at scsibus1 target 0 lun 0: <SONY, PS-SYSTEM   302R, 4062> cdrom removable
uhub4 at uhub1 port 2
umass0 at uhub3 port 1 configuration 1 interface 0
uhub4: Sony GL852-4port, class 9/0, rev 2.00/8.01, addr 2
uhub4: multiple transaction translators
umass0: Sony GL819, rev 2.00/0.09, addr 2
umass0: using SCSI over Bulk-Only
uhub4: 4 ports with 4 removable, self powered
scsibus2 at umass0: 2 targets, 3 luns per target
sd1 at scsibus2 target 0 lun 0: <Sony, GL819 MS, 1.01> disk removable
sd1: drive offline
sd2 at scsibus2 target 0 lun 1: <Sony, GL819 SD, 1.01> disk removable
sd2: drive offline
sd3 at scsibus2 target 0 lun 2: <Sony, GL819 CF, 1.01> disk removable
sd3: drive offline
ubt0 at uhub3 port 2
ubt0: Sony Bluetooth Transceiver, rev 2.00/1.00, addr 3
uplcom0 at uhub4 port 1
uplcom0: Prolific Technology PL2303 Serial adapter (ATEN/IOGEAR UC232A), rev 1.10/2.02, addr 3
ucom0 at uplcom0
boot device: <unknown>
root on gelic0
nfs_boot: trying DHCP/BOOTP
...