Re: L-router / L-board

[Takao Shinohara <shin@sm.sony.co.jp>]

hatano@sarasarado.org (HATANO Hiromichi) writes:
> NetBSDをのせるとかそういう動きはないですか?

カーネルのメッセージが表示できる程度には動くようになりました。

まだ割り込み関係とかを作っていないのでデバイスはシリアルコンソールくらい
しか動いていません。

篠原

# platidとかbootinfoがいんちきなので"Victor InterLink MPC303"と表示され
# ていますが、L-Routerです:-)

--- begin boot message ---
mem_cluster_cnt = 2
mem_clusters[0] = {0x0,0x1a0000}
mem_clusters[1] = {0x1a0000,0x1469000}
loading 0x1a0000,0x1469000
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.5Y (LROUTER) #27: Sat Dec  8 13:19:41 JST 2001
    shin@shinji:/u/src/current/work/src/sys/arch/hpcmips/compile/LROUTER
Victor InterLink MPC303 (NEC VR4122 rev0.3 180.633MHz)
total memory = 22564 KB
avail memory = 19016 KB
using 307 buffers containing 1228 KB of memory
mainbus0 (root)
cpu0 at mainbus0: NEC VR4100 CPU (0xc70) Rev. 7.0 with software emulated floating point Rev. 0.0
cpu0: 32KB/32B direct-mapped L1 Instruction cache, 32 TLB entries
cpu0: 16KB/16B direct-mapped write-back L1 Data cache
vrip0 at mainbus0
vrbcu0 at vrip0 addr 0xf000000-0xf00001f
vrbcu0: cpu 180.633MHz, bus 30.105MHz, ram 60.211MHz
vrcmu0 at vrip0 addr 0xf000060-0xf00007f
vrgiu0 at vrip0 addr 0xf000140-0xf00015f intr 8
com0 at vrip0 addr 0xf000800-0xf000807 intr 9: ns16550a, working fifo
com0: console
vrrtc0 at vrip0 addr 0xf000100-0xf00011f intr 2
vrpmu0 at vrip0 addr 0xf0000c0-0xf0000df intr 1
vrpmu: RESET switch detected
vrled0 at vrip0 addr 0xf000180-0xf00018f intr 17
vrpciu0 at vrip0 addr 0xf000c00-0xf000dff intr 22
pci0 at vrpciu0 bus 0
pci0: i/o space, memory space enabled, rd/line ok
fxp0 at pci0 dev 0 function 0: i82559S Ethernet, rev 9
fxp0: couldn't map interrupt
fxp1 at pci0 dev 1 function 0: i82559S Ethernet, rev 9
trap: TLB miss (load or instr. fetch) in kernel mode
status=0x2, cause=0x8108, epc=0x80142614, vaddr=0x0
pid=0 cmd=swapper usp=0x0 ksp=0x8019f950
Stopped in pid 0 (swapper) at   0x80142614:     lw      v0,0(a0)
db> 
--- end boot message ----